The convex and concave convex fabrics are compact and delicate on the front, with strip or pattern convex patterns, and rough on the back, with long floating lines. Wool fabric: single side woolen fabric, with the pile side being the front side of the fabric. For double-sided fleece fabric, the front side shall be the smooth and tidy side. Observe the selvage of the fabric: if the selvage is smooth, the neat side is the front side of the fabric. For double-layer, multi-layer and multiple fabrics, if the warp and weft density of the front and the back is different, the front side has a larger density or the front side has better raw materials.
If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; The fixing pin of knitting needle is worn; Precautions: change another weft yarn; The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
The so-called water slurry is a kind of water-based slurry. It doesn't have a strong hand feel and coverage when printed on clothes. It is only suitable for printing on light colored fabrics. The price is relatively flat, and it belongs to a lower grade printing category. But it also has an advantage, because it will not affect the original texture of the fabric, so it is more suitable for large-scale printing patterns. It is characterized by soft handle and bright color~~But there is a big disadvantage of the slurry. The color of the slurry is lighter than the cloth color~~If the cloth color is darker, the slurry can not cover at all.
According to the functional data learned by Xiao Bian, the temperature of the lit cigarette is about 700 ℃, and the continuous burning time of a cigarette is about 15 minutes, which is a long time. However, the spontaneous ignition point of common combustibles is very low, such as paper, cotton, linen and knitted fabrics, whose ignition point is mostly 200 ℃ to 300 ℃, so it is easy to cause fire. Turning to the statistics of major and catastrophic fires nationwide, there are many records of fires and casualty accidents caused by smoking after drinking, smoking in bed, littering cigarette butts and other reasons. The typical case is the Great Khingan Mountains forest fire in 1987, which caused a heavy loss of 6.913 billion yuan. It was later discovered that four of the first five fire spots of the fire were caused by human beings, and two of the fire spots were ignited by the cigarette butts of three "smokers".
Harbin Customized Shuttleless webbing Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color, color and texture on the belt surface by naked eye (each needle edge of the ribbon must be of one color) Customized Shuttleless webbing Manufacturer The needle edge and cloth edge cannot be exchanged. Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
The basic process flow of knitting is: bleaching and dyeing - weft rolling - weaving - off machine cutting - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality. In 1980, SD-81A and B rubber ingot belts were developed, which are soft, light, thin, firm, with small elongation, small impact force, short and flat joints. At the beginning of 1990, the trial production of car seat belts for Santana cars was successful. After more than two years of research and trial production, the product quality reached QC49-92 and TL-VW470 standards.
