There are two primary methods for coloring, one is to apply it to a wide range of dyeing (conventional dyeing), and the first is to treat it in chemical dye solution. The other method is to use paint to make the paint into tiny insoluble colored particles to stick to the fabric (dyeing of fibrous material stock solution is not included). Acid dyes are mostly suitable for protein fiber, nylon fiber and silk. It is characterized by beautiful color, poor washing degree and excellent dry cleaning degree. It is widely used in natural dead dyeing.
Guess the pros and cons. It is difficult to identify the front and back sides of some cases and bags because of their special texture. The following is how the luggage and webbing factory teaches you to identify the front and back of the webbing. In fact, we can identify it according to the pattern of the webbing, the front of the pattern is clear and clean, the pattern lines are obvious, the layers are clear, and the color is bright. Generally, the patterns on the front are clearer and more beautiful than those on the back. The front pattern of plant and color matching patterned fabrics with striped appearance must be clear and pleasing. This pattern is especially obvious when weaving jacquard belts.
Hygiene: It is a natural fiber, and its main component is cellulose, with a small amount of waxy substances, nitrogen and pectin. After various inspections and practices, the pure cotton ribbon has no stimulation or negative effect when contacting with the skin. It is beneficial to the human body and has good sanitary performance after being worn for a long time. Heat resistance: the heat resistance is good. When the temperature is below 110 ℃, it will only cause water evaporation on the webbing and will not damage the fiber. Therefore, the use, washing, printing and dyeing of pure cotton webbing at room temperature have no impact on the webbing, which improves the washing and wear resistance of pure cotton edging webbing.
However, due to its hardness, it is not suitable for large area of field patterns. Large area patterns should be printed with water slurry and then dotted with glue slurry, which can not only solve the problem of hard glue in large area, but also highlight the sense of hierarchy of patterns; Another method is to steal a large area of field patterns and make them look bad, but they are always hard to wear. Therefore, it is better to combine water and glue to solve the problem of large area printing. It has smooth surface and matte surface. It has soft, thin, environmental protection and other characteristics, and can be stretched. Generally speaking, glue printing is more commonly used. For leisure brands such as "Yichun", they basically use glue ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡.
It may be due to the use of too much thinner, especially the poor compatibility of thinner and ink, which causes color bleeding during PP textile printing. It may be that there is color seeping on the edge of the printed image and text, which is a common phenomenon, so don't worry too much. It can be solved by ordinary methods. It may be caused by the selection of dyes in the ink, or it can be said that it is caused by the improper matching of pigments. We can deal with the problems in this link according to the situation, and pay attention to the details in this link.
special Single and double layer webbing Manufacturer The basic process flow of knitting is: bleaching and dyeing - weft rolling - weaving - off machine cutting - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the speed to 160~190 rpm and doubled the stand rate, Dalian Single and double layer webbing Manufacturer The product quality has been greatly improved. In 1980, SD-81A and B rubber ingot belts were developed, which are soft, light, thin, firm, with small elongation, small impact force, short and flat joints. At the beginning of 1990, the trial production of car seat belts for Santana cars was successful. After more than two years of research and trial production, the product quality reached QC49-92 and TL-VW470 standards.
