If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; The fixing pin of knitting needle is worn; Precautions: change another weft yarn; The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
Shenyang Brocade ribbon wholesale Silk fabrics have high porosity, so they have good sound absorption, dust absorption and heat resistance. So in addition to making clothes, it can also be used for Shenyang customized Brocade ribbon Interior decoration, such as silk carpet, tapestry, curtain, wall cloth, etc. Decorating a room with silk ornaments can not only make the room spotless, but also keep the room quiet. Due to its hygroscopicity, moisture release performance, moisture retention, air absorption and porosity, it can also adjust the indoor temperature and humidity. Silk fiber has small thermal denaturation and is relatively heat-resistant. When it is heated to 100 ℃, it is only about 5-8% brittle, and the thermal variability of most synthetic fibers is 4-5 times greater than that of silk. The combustion temperature of silk is 300~400 ℃, which is a non combustible fiber, while the combustion temperature of synthetic fiber is 200~2600C, which is flammable and fusible. Therefore, using silk fiber as the raw material for interior decoration can not only play the role of sound absorption, dust absorption, heat preservation, but also play the role of flame retardant.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
What backpack webbing means to bags: It is the end of the year again, and a large-scale movement in history is about to begin, which is the Spring Festival travel. In this wave of people returning home, all kinds of bags and backpack webbing have become a beautiful landscape. What's the meaning of backpacking. Bags are widely used in our daily life, especially in the days of Spring Festival travel. What people carry on their backs, what they carry on their hands, and what they hang around their necks, regardless of where they appear, are the knapsack ribbons that are closely related to the human body. It can be said that it is of great significance. Can you imagine the sour and refreshing feeling brought by the sudden rupture of the bag belt when you are carrying a full case of luggage to board the train?
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
The basic process flow of knitting is: bleaching and dyeing - weft rolling - weaving - off machine cutting - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality. In 1980, SD-81A and B rubber ingot belts were developed, which are soft, light, thin, firm, with small elongation, small impact force, short and flat joints. At the beginning of 1990, the trial production of car seat belts for Santana cars was successful. After more than two years of research and trial production, the product quality reached QC49-92 and TL-VW470 standards.
