In the 1970s, due to the promotion of continuous ribbon dyeing and ironing machine, the processing of ribbon has developed from the traditional process of dyeing before weaving to weaving before dyeing, weaving before bleaching, ironing after processing, and the ribbon technology has entered the ranks of mechanized mass production. In the early 1980s, the industry introduced high-speed shuttleless loom, ironing machine, wrapping machine, warping machine, etc. from Switzerland, Italy and the Federal Republic of Germany, and the ribbon technology entered a new stage of development. The progress of webbing technology has brought about the upgrading of products. In 1980, the rubber ingot belt was developed, which has the characteristics of soft, light, thin, firm, small elongation, small impact force, short and flat joints.
Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
There are two primary methods for coloring, one is to apply it to a wide range of dyeing (conventional dyeing), and the first is to treat it in chemical dye solution. The other method is to use paint to make the paint into tiny insoluble colored particles to stick to the fabric (dyeing of fibrous material stock solution is not included). Acid dyes are mostly suitable for protein fiber, nylon fiber and silk. It is characterized by beautiful color, poor washing degree and excellent dry cleaning degree. It is widely used in natural dead dyeing.
The moisture in the air may cause spots in the car. When this kind of webbing contacts the clothes of passengers, the spots and colors on the luggage webbing will also be transferred to the clothes. Therefore, it should have anti spot fading characteristics, which is also called spot color fastness. The spot color fastness test includes multi fiber test and filter paper test. The multi fiber test is to clamp a sample of tissue belt between two layers of colored cloth. Immerse the mixed colored cloth into the vessel with distilled water and completely wet it. Then squeeze the water out of the extruder, and then clamp these colored cloth wrapped with selvedge webbing into the plexiglass sheet, put it into the sample holder, and lock the sample holder. This rack is placed in a high and low temperature box at a certain temperature, and after reaching the specified time. Take out the sample and hang the colored cloth.
Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
computer make well-connected PP ribbon wholesale The drawing process of. Many friends are interested in computers Customized PP ribbon wholesale I'm particularly interested. Xiao Bian has briefly introduced the textile technology of the computer jacquard belt before, but many people are still interested in how to draw the computer jacquard belt. Today, I will introduce its drawing method according to the drawing process of the ribbon. Single color change: change the color of the left or right mouse button in the picture according to the position within the parameter range, and change the color of a connected color block within the parameter range. The color changed depends on whether the left or right mouse button is pressed. Select a rectangular range: click two points in the editing area to form a rectangular range with these two points as the opposite corners, so that you can clear, cut, copy, and organize this rectangular range. Clear out of parameter drawings: Clear the drawings outside the set range of longitude and latitude.
