The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so the immersion test is required. At room temperature, fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
The convex and concave convex fabrics are compact and delicate on the front, with strip or pattern convex patterns, and rough on the back, with long floating lines. Wool fabric: single side woolen fabric, with the pile side being the front side of the fabric. For double-sided fleece fabric, the front side shall be the smooth and tidy side. Observe the selvage of the fabric: if the selvage is smooth, the neat side is the front side of the fabric. For double-layer, multi-layer and multiple fabrics, if the warp and weft density of the front and the back is different, the front side has a larger density or the front side has better raw materials.
It was by Guangdong customized Cotton ribbon With this performance, silk fabrics are more suitable for direct contact with human skin. Therefore, we can directly wrap a chic garment with silk scarves in the hot summer, which is not only beautiful but also comfortable. Silk not only has good heat dissipation performance, but also has good warmth retention. Its thermal insulation is proud of its porous fiber structure. There are many tiny fibers in a silk fiber, and these tiny fibers are composed of even smaller fibers. Therefore, customized Cotton ribbon wholesale In fact, more than 38% of the seemingly solid silk is hollow. There is a large amount of air in these gaps, which prevents the heat from radiating, making the silk very warm.
The unused ones from the knitting production line are called. The strength, width, thickness, elongation and stiffness described above are all measured on the knitting production line. The data measured on the knitting production line are called data. The safety belt installed in the car should be worn by the passengers after they get on the car. The use process is an aging process, and its strength will decline. In order to ensure that the safety belt can effectively protect the passengers before the vehicle is scrapped, the strength of the webbing shall be measured after simulating the working conditions. This strength is called the strength after the environmental test. After the environmental test, the strength includes light treatment, low temperature treatment, high temperature treatment, immersion test and wear treatment.
In the 1970s, due to the promotion of continuous ribbon dyeing and ironing machine, the processing of ribbon has developed from the traditional process of dyeing before weaving to weaving before dyeing, weaving before bleaching, ironing after processing, and the ribbon technology has entered the ranks of mechanized mass production. In the early 1980s, the industry introduced high-speed shuttleless loom, ironing machine, wrapping machine, warping machine, etc. from Switzerland, Italy and the Federal Republic of Germany, and the ribbon technology entered a new stage of development. The progress of webbing technology has brought about the upgrading of products. In 1980, the rubber ingot belt was developed, which has the characteristics of soft, light, thin, firm, small elongation, small impact force, short and flat joints.
