Anshan special Clothing ribbon Guess the pros and cons. It is difficult to identify the front and back sides of some cases and bags because of their special texture. The following is how the luggage and webbing factory teaches you to identify the front and back of the webbing. In fact, we can identify it according to the pattern of the webbing, the front of the pattern is clear and clean, the pattern lines are obvious, the layers are clear, and the color is bright. commonly Anshan special Clothing ribbon wholesale The patterns on the front are clearer and more beautiful than those on the back. The front pattern of plant and color matching patterned fabrics with striped appearance must be clear and pleasing. This pattern is especially obvious when weaving jacquard belts.
Direct dyes, suitable for cellulosic fabrics, have poor washing fastness and different light fastness, but the modified direct dyes will improve their washing color. Disperse dyes are suitable for viscose, acrylic, nylon, polyester, etc. The fastness to washing is different, polyester is better, and viscose is worse. Azo fuel (Naftol dye) is suitable for cellulosic fabrics. It has beautiful color and is more suitable for beautiful color and luster. Sulfide dyes are suitable, with dim color, mainly dark blue, black and brown, good light resistance and water washing resistance, and poor chlorine bleaching resistance. Long term storage of fabrics will damage fibers.
Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so the immersion test is required. At room temperature, fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
