After the weft tube is formed by the yarn warp cylinder and weft winding, it is inserted on the fixed gear seat of the knitting machine, and the weft tube rotates along the 8-shaped track to draw the yarns to cross weave with each other. Usually, the number of spindles is even, the woven tape is tubular, the number of spindles is odd, and the woven tape is flat. Spindle weaving technology has been applied since old China. The number of spindles varies from 9 to 100 due to different equipment. The basic process of weaving is: bleaching and dyeing - weft rolling - weaving - off machine shearing - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality.
If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; The fixing pin of knitting needle is worn; Precautions: change another weft yarn; The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
Flat screen printing. The printing mould is a polyester or nylon screen (pattern) fixed on a square frame with hollow patterns. The pattern on the pattern plate can pass through the color paste, and the mesh without pattern can be sealed with a polymer film. When printing, the pattern is pressed against the fabric, and the color paste is placed on the pattern. The scraper is used to repeatedly scrape and press the color paste to reach the fabric surface through the pattern. Flat screen printing has low production efficiency, but wide adaptability and flexible application, suitable for small batch and multi variety production. Water slurry printing of bag webbing.
At present, more than 90% of the market is made of cotton polyester thread or polyester cotton thread, but there are few pure cotton threads in the market, and the price is surprisingly high! Polyester cotton yarn just neutralizes the advantages of pure cotton and polyester, depending on the composition of polyester in cotton. Generally, the yarn of cotton ribbon is made by adding a small amount of polyester into cotton, so that it can have the advantages of pure cotton and polyester cotton. It is easy to wash, heat resistant, alkali resistant, moisturizing, sanitary, wear-resistant, not shrink, not easy to wrinkle, not easy to deform, not easy to stick wool, and so on! The key is that the proportion of cotton and polyester is appropriate! The identification method of pure cotton webbing and polyester cotton webbing is simply to take the cut thread and burn it. If there is any hard block, it is polyester cotton yarn containing polyester, and if it is completely reduced to ashes, it is authentic pure cotton.
special 3-strand twisted rope The printing is in the passenger compartment to enhance the matching and coordination with the color in the cabin. The binding ribbon printing will be dyed into various colors. People always hope that the color dyed will not fade within the specified time. Therefore, 3-strand twisted rope manufactor The belt has specific color fastness test. The wrapped webbing belt is exposed to light, and like other substances, it will fade. The wrapped webbing has this characteristic, which is called light color fastness. In this test, the webbing is placed under representative strong light and exposed to the specified time. Then compare the bag webbing with the standard color card to evaluate a fading grade.
According to the functional data learned by Xiao Bian, the temperature of the lit cigarette is about 700 ℃, and the continuous burning time of a cigarette is about 15 minutes, which is a long time. However, the spontaneous ignition point of common combustibles is very low, such as paper, cotton, linen and knitted fabrics, whose ignition point is mostly 200 ℃ to 300 ℃, so it is easy to cause fire. Turning to the statistics of major and catastrophic fires nationwide, there are many records of fires and casualty accidents caused by smoking after drinking, smoking in bed, littering cigarette butts and other reasons. The typical case is the Great Khingan Mountains forest fire in 1987, which caused a heavy loss of 6.913 billion yuan. It was later discovered that four of the first five fire spots of the fire were caused by human beings, and two of the fire spots were ignited by the cigarette butts of three "smokers".
