The printing is in the passenger compartment to enhance the matching and coordination with the color in the cabin. The binding ribbon printing will be dyed into various colors. People always hope that the color dyed will not fade within the specified time. Therefore, the belt has a specific color fastness test. The wrapped webbing belt is exposed to light, and like other substances, it will fade. The wrapped webbing has this characteristic, which is called light color fastness. In this test, the webbing is placed under representative strong light and exposed to the specified time. Then compare the bag webbing with the standard color card to evaluate a fading grade.
How much does a yard weigh? This is for accurate quotation. If you calculate the weight of one yard, you can know how much material is used for this yard of webbing. Is it single-sided or double-sided? Some are divided into single side and double side, so this should also be asked clearly. There are pictures for reference. This is to give us a visual judgment of what is, and give us a more accurate factor of quotation. How many are there? This is a matter of deciding whether to give customers a discount. If there is a large quantity, there must be a discount. Combine factors such as the wages of the factory, the master and the workers.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so the immersion test is required. At room temperature, fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
Selvedge webbing customized Woven belt manufactor What are the characteristics: moisture retention: because the pure cotton edging ribbon is a poor conductor of heat and electricity, its heat conductivity coefficient is extremely low, and because the cotton ribbon itself has the advantages of porosity and high elasticity, a large amount of air can be accumulated between the webbing, and the air is also a bad conductor of heat and electricity, the pure cotton ribbon has good moisture retention customized Woven belt manufactor Pure cotton ribbon makes people feel warm. Hygiene: pure cotton edging webbing is a natural fiber, which is mainly composed of cellulose, a small amount of waxy substances, nitrogen and pectin.
However, due to its hardness, it is not suitable for large area of field patterns. Large area patterns should be printed with water slurry and then dotted with glue slurry, which can not only solve the problem of hard glue in large area, but also highlight the sense of hierarchy of patterns; Another method is to steal a large area of field patterns and make them look bad, but they are always hard to wear. Therefore, it is better to combine water and glue to solve the problem of large area printing. It has smooth surface and matte surface. It has soft, thin, environmental protection and other characteristics, and can be stretched. Generally speaking, glue printing is more commonly used. For leisure brands such as "Yichun", they basically use glue ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡.
