Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
Clear drawings within parameters: clear the drawings within the set range of longitude and latitude. Multiple maps to one map: insert multiple maps into one map in the longitudinal direction. One manufacturing to multiple manufacturing: turn in one drawing and disassemble it into multiple pieces in the longitudinal direction. Graph merging: after multiple graphs are handed over and inserted into one (that is, multiple weaving turns to one manufacturing), the whole warp yarn with one upper and lower weave is deleted. Computer jacquard webbing drawing sequence: analyze the weave rule of the jacquard webbing, draw all the "high" parts of the text or pattern in a cycle according to the weave rule that has been analyzed and determined and the actual fabric, and then draw the "high" parts of the background color (color other than text or pattern) in a cycle according to the weave rule. After all the "high" parts are drawn, The "low" part of the pattern and bottom is drawn according to the analyzed organization rule until the drawing is completed.
Customized Silk double-layer belt manufactor Ink printing. At first glance, ink is not very different from glue, but when glue is printed on smooth fabrics, such as wind clothing, the color fastness is generally poor, and it can be scraped off with a nail, but ink can overcome this shortcoming. Therefore, when making windbreaker, it is usually printed with ink, with bright color and vivid image. Shenyang Customized Silk double-layer belt There has been a wave of head prints in the market some time ago~I don't know if you have noticed it, then the clear and ultra realistic printing can only be printed with ink in general~Sometimes you can sprinkle gold powder and silver powder on the ink, and feel that the decoration effect is better.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
In this business, there is no doubt that the quotation is very important. I think many colleagues who make webbing are very familiar with their own products and can quote their own prices when they get their own products. If you come across a ribbon that is not made by yourself, can you quote an accurate price? I think it is impossible. Here is a brief introduction to how to quote an accurate price for a ribbon. First of all, the customer needs to understand this ribbon and be able to answer any question clearly.
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
