It is widely used. Xiaobian will briefly introduce some problems, hoping to help the wholesale friends of selvedge webbing. Main materials: nylon webbing, nylon webbing, cotton webbing, polyester webbing, pp webbing, bamboo fiber and other production processes: textile is a traditional industry in China with a long history. As early as the Tang Dynasty, Chinese textiles have crossed the vast ocean to benefit the world. Today, the textile industry is still a strong industry in China.
The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so the immersion test is required. At room temperature, fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
In the 1970s, due to the promotion of continuous ribbon dyeing and ironing machine, the processing of ribbon has developed from the traditional process of dyeing before weaving to weaving before dyeing, weaving before bleaching, ironing after processing, and the ribbon technology has entered the ranks of mechanized mass production. In the early 1980s, the industry introduced high-speed shuttleless loom, ironing machine, wrapping machine, warping machine, etc. from Switzerland, Italy and the Federal Republic of Germany, and the ribbon technology entered a new stage of development. The progress of webbing technology has brought about the upgrading of products. In 1980, the rubber ingot belt was developed, which has the characteristics of soft, light, thin, firm, small elongation, small impact force, short and flat joints.
The narrow Shenzhen ribbon or tubular fabric is made from various yarns. There are many kinds of belt fabrics, which are widely used in clothing, shoes, bags, industry, agriculture, military supplies, transportation and other industrial sectors. In the 1930s, it was all handmade workshops that produced exquisite pictures of ribbons. The raw materials were cotton thread and hemp thread. After the founding of the People's Republic of China, the raw materials for ribbon gradually developed to nylon, vinylon, polyester, polypropylene, spandex, viscose, etc., forming three major types of technology: weaving, knitting, knitting. The fabric structure includes plain weave, twill, satin, jacquard, double-layer, multi-layer, tubular and combined weave.
Jilin Customized Brocade ribbon Steps of printing Brocade ribbon about Brocade ribbon wholesale Many friends don't know how to print, but there are actually two methods. So the master of PP Ribbon Factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
