The so-called water slurry is a kind of water-based slurry. It doesn't have a strong hand feel and coverage when printed on clothes. It is only suitable for printing on light colored fabrics. The price is relatively flat, and it belongs to a lower grade printing category. But it also has an advantage, because it will not affect the original texture of the fabric, so it is more suitable for large-scale printing patterns. It is characterized by soft handle and bright color~~But there is a big disadvantage of the slurry. The color of the slurry is lighter than the cloth color~~If the cloth color is darker, the slurry can not cover at all.
Causes of bleeding. Some customers will customize the printing, but the PP fabric manufacturers sometimes have color bleeding when printing the PP ribbon, so the manufacturers should pay attention to the reasons when printing. Only by understanding these reasons can we reduce the occurrence of various conditions in the future use. What are the reasons for color bleeding when printing? There is dirt on the surface of the machine during printing. Cleaning up during production can reduce these problems.
Hygiene: It is a natural fiber, and its main component is cellulose, with a small amount of waxy substances, nitrogen and pectin. After various inspections and practices, the pure cotton ribbon has no stimulation or negative effect when contacting with the skin. It is beneficial to the human body and has good sanitary performance after being worn for a long time. Heat resistance: the heat resistance is good. When the temperature is below 110 ℃, it will only cause water evaporation on the webbing and will not damage the fiber. Therefore, the use, washing, printing and dyeing of pure cotton webbing at room temperature have no impact on the webbing, which improves the washing and wear resistance of pure cotton edging webbing.
The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so the immersion test is required. At room temperature, fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
Dalian customized Braided rope Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. customized Braided rope wholesale Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
