Silk fabrics have high porosity, so they have good sound absorption, dust absorption and heat resistance. Therefore, in addition to making clothes, it can also be used for interior decoration, such as silk carpets, tapestries, curtains, wall coverings, etc. Decorating a room with silk ornaments can not only make the room spotless, but also keep the room quiet. Due to its hygroscopicity, moisture release performance, moisture retention, air absorption and porosity, it can also adjust the indoor temperature and humidity. Silk fiber has small thermal denaturation and is relatively heat-resistant. When it is heated to 100 ℃, it is only about 5-8% brittle, and the thermal variability of most synthetic fibers is 4-5 times greater than that of silk. The combustion temperature of silk is 300~400 ℃, which is a non combustible fiber, while the combustion temperature of synthetic fiber is 200~2600C, which is flammable and fusible. Therefore, using silk fiber as the raw material for interior decoration can not only play the role of sound absorption, dust absorption, heat preservation, but also play the role of flame retardant.
Jilin special Electrical tape The convex and concave convex fabrics are compact and delicate on the front, with strip or pattern convex patterns, and rough on the back, with long floating lines. Wool fabric: single side woolen fabric, with the pile side being the front side of the fabric. For double-sided fleece fabric, the front side shall be the smooth and tidy side. special Electrical tape Manufacturer Observe the selvage of the fabric: if the selvage is smooth, the neat side is the front side of the fabric. For double-layer, multi-layer and multiple fabrics, if the warp and weft density of the front and the back is different, the front side has a larger density or the front side has better raw materials.
Ink printing. At first glance, ink is not very different from glue, but when glue is printed on smooth fabrics, such as wind clothing, the color fastness is generally poor, and it can be scraped off with a nail, but ink can overcome this shortcoming. Therefore, when making windbreaker, it is usually printed with ink, with bright color and vivid image. There has been a wave of head prints in the market some time ago~I don't know if you have noticed it, then the clear and ultra realistic printing can only be printed with ink in general~Sometimes you can sprinkle gold powder and silver powder on the ink, and feel that the decoration effect is better.
If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; The fixing pin of knitting needle is worn; Precautions: change another weft yarn; The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
As an industrial product, it also has its own standard service life, which determines the length of our actual use of webbing. Generally, there are two kinds of situations at the end of use. One is the problem of quality or external damage within the service life, so it can no longer be used. The other is the problem of natural wear and fracture, which is natural damage. It is also inevitable. Today we will talk about the life span in detail. How long is the life span?
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
