If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; The fixing pin of knitting needle is worn; Precautions: change another weft yarn; The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
special Brocade ribbon Manufacturer Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. Fujian special Brocade ribbon Manufacturer The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
After the weft tube is formed by the yarn warp cylinder and weft winding, it is inserted on the fixed gear seat of the knitting machine, and the weft tube rotates along the 8-shaped track to draw the yarns to cross weave with each other. Usually, the number of spindles is even, the woven tape is tubular, the number of spindles is odd, and the woven tape is flat. Spindle weaving technology has been applied since old China. The number of spindles varies from 9 to 100 due to different equipment. The basic process of weaving is: bleaching and dyeing - weft rolling - weaving - off machine shearing - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality.
Causes of bleeding. Some customers will customize the printing, but the PP fabric manufacturers sometimes have color bleeding when printing the PP ribbon, so the manufacturers should pay attention to the reasons when printing. Only by understanding these reasons can we reduce the occurrence of various conditions in the future use. What are the reasons for color bleeding when printing? There is dirt on the surface of the machine during printing. Cleaning up during production can reduce these problems.
