According to the functional data learned by Xiao Bian, the temperature of the lit cigarette is about 700 ℃, and the continuous burning time of a cigarette is about 15 minutes, which is a long time. However, the spontaneous ignition point of common combustibles is very low, such as paper, cotton, linen and knitted fabrics, whose ignition point is mostly 200 ℃ to 300 ℃, so it is easy to cause fire. Turning to the statistics of major and catastrophic fires nationwide, there are many records of fires and casualty accidents caused by smoking after drinking, smoking in bed, littering cigarette butts and other reasons. The typical case is the Great Khingan Mountains forest fire in 1987, which caused a heavy loss of 6.913 billion yuan. It was later discovered that four of the first five fire spots of the fire were caused by human beings, and two of the fire spots were ignited by the cigarette butts of three "smokers".
Silk fabrics have high porosity, so they have good sound absorption, dust absorption and heat resistance. Therefore, in addition to making clothes, it can also be used for interior decoration, such as silk carpets, tapestries, curtains, wall coverings, etc. Decorating a room with silk ornaments can not only make the room spotless, but also keep the room quiet. Due to its hygroscopicity, moisture release performance, moisture retention, air absorption and porosity, it can also adjust the indoor temperature and humidity. Silk fiber has small thermal denaturation and is relatively heat-resistant. When it is heated to 100 ℃, it is only about 5-8% brittle, and the thermal variability of most synthetic fibers is 4-5 times greater than that of silk. The combustion temperature of silk is 300~400 ℃, which is a non combustible fiber, while the combustion temperature of synthetic fiber is 200~2600C, which is flammable and fusible. Therefore, using silk fiber as the raw material for interior decoration can not only play the role of sound absorption, dust absorption, heat preservation, but also play the role of flame retardant.
Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
Gongzhuling special Glass cv webbing Flat screen printing. The printing mould is a polyester or nylon screen (pattern) fixed on a square frame with hollow patterns. The pattern on the pattern plate can pass through the color paste, and the mesh without pattern can be sealed with a polymer film. When printing, the pattern is pressed against the fabric, and the color paste is placed on the pattern. The scraper is used to repeatedly scrape and press the color paste to reach the fabric surface through the pattern. special Glass cv webbing Flat screen printing has low production efficiency, but wide adaptability and flexible application, suitable for small batch and multi variety production. Water slurry printing of bag webbing.
The moisture in the air may cause spots in the car. When this kind of webbing contacts the clothes of passengers, the spots and colors on the luggage webbing will also be transferred to the clothes. Therefore, it should have anti spot fading characteristics, which is also called spot color fastness. The spot color fastness test includes multi fiber test and filter paper test. The multi fiber test is to clamp a sample of tissue belt between two layers of colored cloth. Immerse the mixed colored cloth into the vessel with distilled water and completely wet it. Then squeeze the water out of the extruder, and then clamp these colored cloth wrapped with selvedge webbing into the plexiglass sheet, put it into the sample holder, and lock the sample holder. This rack is placed in a high and low temperature box at a certain temperature, and after reaching the specified time. Take out the sample and hang the colored cloth.
In this business, there is no doubt that the quotation is very important. I think many colleagues who make webbing are very familiar with their own products and can quote their own prices when they get their own products. If you come across a ribbon that is not made by yourself, can you quote an accurate price? I think it is impossible. Here is a brief introduction to how to quote an accurate price for a ribbon. First of all, the customer needs to understand this ribbon and be able to answer any question clearly.
