Causes of bleeding. Some customers will customize the printing, but the PP fabric manufacturers sometimes have color bleeding when printing the PP ribbon, so the manufacturers should pay attention to the reasons when printing. Only by understanding these reasons can we reduce the occurrence of various conditions in the future use. What are the reasons for color bleeding when printing? There is dirt on the surface of the machine during printing. Cleaning up during production can reduce these problems.
Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
In the 1970s, due to the promotion of continuous ribbon dyeing and ironing machine, the processing of ribbon has developed from the traditional process of dyeing before weaving to weaving before dyeing, weaving before bleaching, ironing after processing, and the ribbon technology has entered the ranks of mechanized mass production. In the early 1980s, the industry introduced high-speed shuttleless loom, ironing machine, wrapping machine, warping machine, etc. from Switzerland, Italy and the Federal Republic of Germany, and the ribbon technology entered a new stage of development. The progress of webbing technology has brought about the upgrading of products. In 1980, the rubber ingot belt was developed, which has the characteristics of soft, light, thin, firm, small elongation, small impact force, short and flat joints.
Siping special Brocade ribbon The convex and concave convex fabrics are compact and delicate on the front, with strip or pattern convex patterns, and rough on the back, with long floating lines. Wool fabric: single side woolen fabric, with the pile side being the front side of the fabric. For double-sided fleece fabric, the front side shall be the smooth and tidy side. special Brocade ribbon manufactor Observe the selvage of the fabric: if the selvage is smooth, the neat side is the front side of the fabric. For double-layer, multi-layer and multiple fabrics, if the warp and weft density of the front and the back is different, the front side has a larger density or the front side has better raw materials.
The so-called water slurry is a kind of water-based slurry. It doesn't have a strong hand feel and coverage when printed on clothes. It is only suitable for printing on light colored fabrics. The price is relatively flat, and it belongs to a lower grade printing category. But it also has an advantage, because it will not affect the original texture of the fabric, so it is more suitable for large-scale printing patterns. It is characterized by soft handle and bright color~~But there is a big disadvantage of the slurry. The color of the slurry is lighter than the cloth color~~If the cloth color is darker, the slurry can not cover at all.
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
