Flat screen printing. The printing mould is a polyester or nylon screen (pattern) fixed on a square frame with hollow patterns. The pattern on the pattern plate can pass through the color paste, and the mesh without pattern can be sealed with a polymer film. When printing, the pattern is pressed against the fabric, and the color paste is placed on the pattern. The scraper is used to repeatedly scrape and press the color paste to reach the fabric surface through the pattern. Flat screen printing has low production efficiency, but wide adaptability and flexible application, suitable for small batch and multi variety production. Water slurry printing of bag webbing.
Harbin special Aramid tape Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. special Aramid tape manufactor Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so the immersion test is required. At room temperature, fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
The longitude and latitude are interwoven. [Subject] After twisting, the yarn is warped into a bobbin (pan head), and the weft yarn is shaken into a bobbin, which is woven on the loom. In the 1930s, it was used for hand looms and iron wood looms. In the early 1960s, the 1511 loom was converted into a belt loom, which is still widely used. Due to the small width of the belt, the weaving methods are different, ranging from single, double, dozens of pieces, from single layer to double layer. In 1967, the research group of shuttleless weaving belt with workers as the main body in the industry successfully designed and manufactured a high-speed single shuttleless loom by itself, which realized that the weaving belt does not need shuttles, and the process is shortened, the floor area is small, and the labor productivity is improved, which is an innovation in the history of Chinese weaving belt technology.
Silk fabrics have high porosity, so they have good sound absorption, dust absorption and heat resistance. Therefore, in addition to making clothes, it can also be used for interior decoration, such as silk carpets, tapestries, curtains, wall coverings, etc. Decorating a room with silk ornaments can not only make the room spotless, but also keep the room quiet. Due to its hygroscopicity, moisture release performance, moisture retention, air absorption and porosity, it can also adjust the indoor temperature and humidity. Silk fiber has small thermal denaturation and is relatively heat-resistant. When it is heated to 100 ℃, it is only about 5-8% brittle, and the thermal variability of most synthetic fibers is 4-5 times greater than that of silk. The combustion temperature of silk is 300~400 ℃, which is a non combustible fiber, while the combustion temperature of synthetic fiber is 200~2600C, which is flammable and fusible. Therefore, using silk fiber as the raw material for interior decoration can not only play the role of sound absorption, dust absorption, heat preservation, but also play the role of flame retardant.
Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
