Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
It is precisely because of this performance that silk fabrics are more suitable for direct contact with human skin. Therefore, we can directly wrap a unique garment with silk scarves in the hot summer, which is not only beautiful but also comfortable. Silk not only has good heat dissipation performance, but also has good warmth retention. Its thermal insulation is proud of its porous fiber structure. There are many tiny fibers in a silk fiber, and these tiny fibers are composed of even smaller fibers. Therefore, more than 38% of the seemingly solid silk is actually hollow, and there is a large amount of air in these gaps, which prevents the heat emission and makes the silk have good warmth retention.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
Unused products from knitting production line are called Fujian Selvedge webbing The strength, width, thickness, elongation and stiffness described above are all Fujian special Selvedge webbing These measured data are called Selvedge webbing Data. The safety belt installed in the car should be worn by the passengers after they get on the car. The use process is an aging process, and its strength will decline. In order to ensure that the safety belt can effectively protect the passengers before the vehicle is scrapped, the strength of the webbing shall be measured after simulating the working conditions. This strength is called the strength after the environmental test special Selvedge webbing strength. After the environmental test, the strength includes light treatment, low temperature treatment, high temperature treatment, immersion test and wear treatment.
The basic process flow of knitting is: bleaching and dyeing - weft rolling - weaving - off machine cutting - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality. In 1980, SD-81A and B rubber ingot belts were developed, which are soft, light, thin, firm, with small elongation, small impact force, short and flat joints. At the beginning of 1990, the trial production of car seat belts for Santana cars was successful. After more than two years of research and trial production, the product quality reached QC49-92 and TL-VW470 standards.
How much does a yard weigh? This is for accurate quotation. If you calculate the weight of one yard, you can know how much material is used for this yard of webbing. Is it single-sided or double-sided? Some are divided into single side and double side, so this should also be asked clearly. There are pictures for reference. This is to give us a visual judgment of what is, and give us a more accurate factor of quotation. How many are there? This is a matter of deciding whether to give customers a discount. If there is a large quantity, there must be a discount. Combine factors such as the wages of the factory, the master and the workers.
