One of the complete knowledge of printing types. There are many kinds of bag ribbon printing. Today, it is divided into two parts for everyone to talk about. If you like it, you can have a detailed look. It should be helpful to you. Here is the first part. Bag webbing transfer printing. The pigment is printed on the paper by printing method to make transfer printing paper, and then the color is transferred to the fabric by high temperature (heating and pressing on the back of the paper). It is generally used for chemical fiber fabrics, characterized by bright colors, fine layers, lifelike patterns, and strong artistry. However, this process is currently only applicable to a few synthetic fibers such as polyester. Transfer printing process is simple, investment is small and production is flexible. It is popular in the market at present But to be honest, compared with other types of printing, the price of this transfer printing is a little high, but it has a certain level.
Fuzhou special Single and double layer webbing Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. special Single and double layer webbing manufactor Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
However, due to its hardness, it is not suitable for large area of field patterns. Large area patterns should be printed with water slurry and then dotted with glue slurry, which can not only solve the problem of hard glue in large area, but also highlight the sense of hierarchy of patterns; Another method is to steal a large area of field patterns and make them look bad, but they are always hard to wear. Therefore, it is better to combine water and glue to solve the problem of large area printing. It has smooth surface and matte surface. It has soft, thin, environmental protection and other characteristics, and can be stretched. Generally speaking, glue printing is more commonly used. For leisure brands such as "Yichun", they basically use glue ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡.
At present, more than 90% of the market is made of cotton polyester thread or polyester cotton thread, but there are few pure cotton threads in the market, and the price is surprisingly high! Polyester cotton yarn just neutralizes the advantages of pure cotton and polyester, depending on the composition of polyester in cotton. Generally, the yarn of cotton ribbon is made by adding a small amount of polyester into cotton, so that it can have the advantages of pure cotton and polyester cotton. It is easy to wash, heat resistant, alkali resistant, moisturizing, sanitary, wear-resistant, not shrink, not easy to wrinkle, not easy to deform, not easy to stick wool, and so on! The key is that the proportion of cotton and polyester is appropriate! The identification method of pure cotton webbing and polyester cotton webbing is simply to take the cut thread and burn it. If there is any hard block, it is polyester cotton yarn containing polyester, and if it is completely reduced to ashes, it is authentic pure cotton.
The longitude and latitude are interwoven. [Subject] After twisting, the yarn is warped into a bobbin (pan head), and the weft yarn is shaken into a bobbin, which is woven on the loom. In the 1930s, it was used for hand looms and iron wood looms. In the early 1960s, the 1511 loom was converted into a belt loom, which is still widely used. Due to the small width of the belt, the weaving methods are different, ranging from single, double, dozens of pieces, from single layer to double layer. In 1967, the research group of shuttleless weaving belt with workers as the main body in the industry successfully designed and manufactured a high-speed single shuttleless loom by itself, which realized that the weaving belt does not need shuttles, and the process is shortened, the floor area is small, and the labor productivity is improved, which is an innovation in the history of Chinese weaving belt technology.
