Silk fabrics have high porosity, so they have good sound absorption, dust absorption and heat resistance. Therefore, in addition to making clothes, it can also be used for interior decoration, such as silk carpets, tapestries, curtains, wall coverings, etc. Decorating a room with silk ornaments can not only make the room spotless, but also keep the room quiet. Due to its hygroscopicity, moisture release performance, moisture retention, air absorption and porosity, it can also adjust the indoor temperature and humidity. Silk fiber has small thermal denaturation and is relatively heat-resistant. When it is heated to 100 ℃, it is only about 5-8% brittle, and the thermal variability of most synthetic fibers is 4-5 times greater than that of silk. The combustion temperature of silk is 300~400 ℃, which is a non combustible fiber, while the combustion temperature of synthetic fiber is 200~2600C, which is flammable and fusible. Therefore, using silk fiber as the raw material for interior decoration can not only play the role of sound absorption, dust absorption, heat preservation, but also play the role of flame retardant.
More than 90% of the market Liaoning customized Electrical tape It is made of cotton polyester thread or polyester cotton thread, but pure cotton thread is rare in the market, and the price is surprisingly high! Polyester cotton yarn just neutralizes the advantages of pure cotton and polyester, depending on the composition of polyester in cotton. Generally, the yarn of cotton ribbon is made by adding a small amount of polyester into cotton, so that it can have the advantages of pure cotton and polyester cotton. It is easy to wash, heat resistant, alkali resistant, moisturizing, sanitary, wear-resistant, not shrink, not easy to wrinkle, not easy to deform, not easy to stick wool, and so on! Liaoning Electrical tape wholesale The key is that the proportion of cotton and polyester is appropriate! The identification method of pure cotton webbing and polyester cotton webbing is simply to take the cut thread and burn it. If there is any hard block, it is polyester cotton yarn containing polyester, and if it is completely reduced to ashes, it is authentic pure cotton.
The moisture in the air may cause spots in the car. When this kind of webbing contacts the clothes of passengers, the spots and colors on the luggage webbing will also be transferred to the clothes. Therefore, it should have anti spot fading characteristics, which is also called spot color fastness. The spot color fastness test includes multi fiber test and filter paper test. The multi fiber test is to clamp a sample of tissue belt between two layers of colored cloth. Immerse the mixed colored cloth into the vessel with distilled water and completely wet it. Then squeeze the water out of the extruder, and then clamp these colored cloth wrapped with selvedge webbing into the plexiglass sheet, put it into the sample holder, and lock the sample holder. This rack is placed in a high and low temperature box at a certain temperature, and after reaching the specified time. Take out the sample and hang the colored cloth.
Under normal use, the general use time is about three years. After three years, because of natural wear, part of the pp webbing will be corroded and broken. But this is under normal use. If it is not used frequently, similar situations will not occur. The reason why most of them cannot be used for such a long time is because they are lost in advance rather than because of other external damage. Therefore, the advice of Xiaobian is not to worry too much about the service life of the PP webbing, but to pay attention to how to protect yourself from loss and trouble.
The convex and concave convex fabrics are compact and delicate on the front, with strip or pattern convex patterns, and rough on the back, with long floating lines. Wool fabric: single side woolen fabric, with the pile side being the front side of the fabric. For double-sided fleece fabric, the front side shall be the smooth and tidy side. Observe the selvage of the fabric: if the selvage is smooth, the neat side is the front side of the fabric. For double-layer, multi-layer and multiple fabrics, if the warp and weft density of the front and the back is different, the front side has a larger density or the front side has better raw materials.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
