After the weft tube is formed by the yarn warp cylinder and weft winding, it is inserted on the fixed gear seat of the knitting machine, and the weft tube rotates along the 8-shaped track to draw the yarns to cross weave with each other. Usually, the number of spindles is even, the woven tape is tubular, the number of spindles is odd, and the woven tape is flat. Spindle weaving technology has been applied since old China. The number of spindles varies from 9 to 100 due to different equipment. The basic process of weaving is: bleaching and dyeing - weft rolling - weaving - off machine shearing - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality.
The basic process flow of knitting is: bleaching and dyeing - weft rolling - weaving - off machine cutting - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality. In 1980, SD-81A and B rubber ingot belts were developed, which are soft, light, thin, firm, with small elongation, small impact force, short and flat joints. At the beginning of 1990, the trial production of car seat belts for Santana cars was successful. After more than two years of research and trial production, the product quality reached QC49-92 and TL-VW470 standards.
Guangdong special Woven belt Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. special Woven belt Manufacturer Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
What are the characteristics of the edging webbing: moisture retention: because the pure cotton edging webbing is a poor conductor of heat and electricity, the heat conductivity coefficient is extremely low, and because the cotton webbing itself has the advantages of porosity and high elasticity, a large amount of air can be accumulated between the webbing, and the air is a bad conductor of heat and electricity, the pure cotton webbing has good moisture retention, and people feel warm when using the pure cotton webbing. Hygiene: pure cotton edging webbing is a natural fiber, which is mainly composed of cellulose, a small amount of waxy substances, nitrogen and pectin.
Xiao Bian always believes that any backpack and webbing factory needs to constantly promote safety in production. In addition to conventional production safety and personal safety of employees, fire prevention should be an important part of this safety. The industry is a flammable industry, because a large number of various yarns and finished webbing products stacked in its workshops are flammable, its safety is directly related to human life safety. Therefore, it is important for enterprises to prevent fire. In the past two years, there have been fires in many ribbon factories across the country, which has caused huge property losses to enterprises. The frequent occurrence of fires in the ribbon industry has also sounded a safety alarm for us. The safety of the company is also closely related to the employees. As a member of the company, fire prevention should start from self. Do not smoke in the factory. If you want to smoke, please go to the specified smoking area. Don't throw cigarette butts everywhere, let yourself be a part, and protect our safety together.
