Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
It was by Jilin special Cotton ribbon With this performance, silk fabrics are more suitable for direct contact with human skin. Therefore, we can directly wrap a chic garment with silk scarves in the hot summer, which is not only beautiful but also comfortable. Silk not only has good heat dissipation performance, but also has good warmth retention. Its thermal insulation is proud of its porous fiber structure. There are many tiny fibers in a silk fiber, and these tiny fibers are composed of even smaller fibers. Therefore, special Cotton ribbon Manufacturer In fact, more than 38% of the seemingly solid silk is hollow. There is a large amount of air in these gaps, which prevents the heat from radiating, making the silk very warm.
What are the characteristics of the edging webbing: moisture retention: because the pure cotton edging webbing is a poor conductor of heat and electricity, the heat conductivity coefficient is extremely low, and because the cotton webbing itself has the advantages of porosity and high elasticity, a large amount of air can be accumulated between the webbing, and the air is a bad conductor of heat and electricity, the pure cotton webbing has good moisture retention, and people feel warm when using the pure cotton webbing. Hygiene: pure cotton edging webbing is a natural fiber, which is mainly composed of cellulose, a small amount of waxy substances, nitrogen and pectin.
The progress of process technology has brought about the upgrading of edging webbing products. In 1979, the trial production of the domestic generation SD9-9 rubber ingot belt was successful, which ended the history of rubber ingot belt products relying on imports. After the weft tube is formed by the yarn warp cylinder and weft winding, it is inserted on the fixed gear seat of the knitting machine, and the weft tube rotates along the 8-shaped track to draw the yarns to cross weave with each other. Usually, the number of spindles is even, the woven tape is tubular, the number of spindles is odd, and the woven tape is flat. Spindle weaving technology has been applied since old China. The number of spindles varies from 9 to 100 due to different equipment.
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
Causes of bleeding. Some customers will customize the printing, but the PP fabric manufacturers sometimes have color bleeding when printing the PP ribbon, so the manufacturers should pay attention to the reasons when printing. Only by understanding these reasons can we reduce the occurrence of various conditions in the future use. What are the reasons for color bleeding when printing? There is dirt on the surface of the machine during printing. Cleaning up during production can reduce these problems.
