Silk fabrics have high porosity, so they have good sound absorption, dust absorption and heat resistance. Therefore, in addition to making clothes, it can also be used for interior decoration, such as silk carpets, tapestries, curtains, wall coverings, etc. Decorating a room with silk ornaments can not only make the room spotless, but also keep the room quiet. Due to its hygroscopicity, moisture release performance, moisture retention, air absorption and porosity, it can also adjust the indoor temperature and humidity. Silk fiber has small thermal denaturation and is relatively heat-resistant. When it is heated to 100 ℃, it is only about 5-8% brittle, and the thermal variability of most synthetic fibers is 4-5 times greater than that of silk. The combustion temperature of silk is 300~400 ℃, which is a non combustible fiber, while the combustion temperature of synthetic fiber is 200~2600C, which is flammable and fusible. Therefore, using silk fiber as the raw material for interior decoration can not only play the role of sound absorption, dust absorption, heat preservation, but also play the role of flame retardant.
If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; The fixing pin of knitting needle is worn; Precautions: change another weft yarn; The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
In the 1970s, due to the promotion of continuous ribbon dyeing and ironing machine, Heihe River Brocade ribbon manufactor From the traditional process of dyeing before weaving to the continuous process of weaving before dyeing, weaving before bleaching, ironing after treatment, the ribbon technology has entered the ranks of mechanized mass production. In the early 1980s, the industry introduced high-speed shuttleless loom, ironing machine, wrapping machine, warping machine, etc. from Switzerland, Italy and the Federal Republic of Germany, and the ribbon technology entered a new stage of development. The progress of webbing technology has brought about the upgrading of products. In 1980, Customized Brocade ribbon manufactor The rubber ingot belt has the characteristics of soft, light, thin, firm, small elongation, small impact force, short and flat joints.
According to the functional data learned by Xiao Bian, the temperature of the lit cigarette is about 700 ℃, and the continuous burning time of a cigarette is about 15 minutes, which is a long time. However, the spontaneous ignition point of common combustibles is very low, such as paper, cotton, linen and knitted fabrics, whose ignition point is mostly 200 ℃ to 300 ℃, so it is easy to cause fire. Turning to the statistics of major and catastrophic fires nationwide, there are many records of fires and casualty accidents caused by smoking after drinking, smoking in bed, littering cigarette butts and other reasons. The typical case is the Great Khingan Mountains forest fire in 1987, which caused a heavy loss of 6.913 billion yuan. It was later discovered that four of the first five fire spots of the fire were caused by human beings, and two of the fire spots were ignited by the cigarette butts of three "smokers".
