Flat screen printing. The printing mould is a polyester or nylon screen (pattern) fixed on a square frame with hollow patterns. The pattern on the pattern plate can pass through the color paste, and the mesh without pattern can be sealed with a polymer film. When printing, the pattern is pressed against the fabric, and the color paste is placed on the pattern. The scraper is used to repeatedly scrape and press the color paste to reach the fabric surface through the pattern. Flat screen printing has low production efficiency, but wide adaptability and flexible application, suitable for small batch and multi variety production. Water slurry printing of bag webbing.
The steps of printing. Many friends don't know how to do it. In fact, there are two methods. So the master of PP ribbon factory will let you know. Direct plate making method: the method of direct plate making is to first place the photosensitive film of the wrist plate base coated with photosensitive material face up on the working table, place the stretched wrist net frame flat on the film base, then put photosensitive paste in the screen frame and apply pressure coating with a soft scraper, remove the plastic film base after drying and filling, and attach the photosensitive film wrist screen for printing. After developing After drying, screen printing is made. Process flow: stretched screen - degreasing - drying - peeling substrate - exposure - development - drying - revision - blocking
Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
Clear drawings within parameters: clear the drawings within the set range of longitude and latitude. Multiple maps to one map: insert multiple maps into one map in the longitudinal direction. One manufacturing to multiple manufacturing: turn in one drawing and disassemble it into multiple pieces in the longitudinal direction. Graph merging: after multiple graphs are handed over and inserted into one (that is, multiple weaves are transformed into one weaves), the whole warp is deleted. Computer jacquard webbing drawing sequence: analyze the weave rule of the jacquard webbing, draw all the "high" parts of the text or pattern in a cycle according to the weave rule that has been analyzed and determined and the actual fabric, and then draw the "high" parts of the background color (color other than text or pattern) in a cycle according to the weave rule. After all the "high" parts are drawn, The "low" part of the pattern and bottom is drawn according to the analyzed organization rule until the drawing is completed.
Xiao Bian always believes that any backpack and webbing factory needs to constantly promote safety in production. In addition to conventional production safety and personal safety of employees, fire prevention should be an important part of this safety. The industry is a flammable industry, because a large number of various yarns and finished webbing products stacked in its workshops are flammable, its safety is directly related to human life safety. Therefore, it is important for enterprises to prevent fire. In the past two years, there have been fires in many ribbon factories across the country, which has caused huge property losses to enterprises. The frequent occurrence of fires in the ribbon industry has also sounded a safety alarm for us. The safety of the company is also closely related to the employees. As a member of the company, fire prevention should start from self. Do not smoke in the factory. If you want to smoke, please go to the specified smoking area. Don't throw cigarette butts everywhere, let yourself be a part, and protect our safety together.
customized Single and double layer belt Manufacturer If the weft needle is damaged, replace it or beat it with gauze; If the steel buckle is damaged, hit it with gauze or replace the steel buckle; The coir filament piece is damaged or the shutdown piece is damaged. Replace it with a new one. Causes of poor needle edge: uneven weft yarn thickness; The knitting needle is not properly laid, too long or too short; The pan head moves abnormally, sometimes tight, sometimes loose; The weft wheel is not round enough and deformed; Wear of the fixed pin of the knitting needle; Precautions: change another weft yarn; Fujian customized Single and double layer belt The knitting needle is longer or shorter according to the thickness of the ribbon. Generally speaking, the length of the knitting needle is just enough to remove the weft; Fix both sides of the pan head firmly, and do not let the pan head lean against the iron frame on both sides; Replace the weft wheel with a new one; Replace the fixed rod or go to processing.
