It is widely used. Xiaobian will briefly introduce some problems, hoping to help the wholesale friends of selvedge webbing. Main materials: nylon webbing, nylon webbing, cotton webbing, polyester webbing, pp webbing, bamboo fiber and other production processes: textile is a traditional industry in China with a long history. As early as the Tang Dynasty, Chinese textiles have crossed the vast ocean to benefit the world. Today, the textile industry is still a strong industry in China.
Clear drawings within parameters: clear the drawings within the set range of longitude and latitude. Multiple maps to one map: insert multiple maps into one map in the longitudinal direction. One manufacturing to multiple manufacturing: turn in one drawing and disassemble it into multiple pieces in the longitudinal direction. Graph merging: after multiple graphs are handed over and inserted into one (that is, multiple weaving turns to one manufacturing), the whole warp yarn with one upper and lower weave is deleted. Computer jacquard webbing drawing sequence: analyze the weave rule of the jacquard webbing, draw all the "high" parts of the text or pattern in a cycle according to the weave rule that has been analyzed and determined and the actual fabric, and then draw the "high" parts of the background color (color other than text or pattern) in a cycle according to the weave rule. After all the "high" parts are drawn, The "low" part of the pattern and bottom is drawn according to the analyzed organization rule until the drawing is completed.
Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
Customized Electrical tape It may be due to the use of too much thinner, especially the poor compatibility of thinner and ink, which causes color bleeding during PP textile printing. It may be that there is color seeping on the edge of the printed image and text, which is a common phenomenon, so don't worry too much. It can be solved by ordinary methods. It may be caused by the selection of dyes in the ink, or it can be said that Harbin Customized Electrical tape It is caused by improper matching of pigments. We can deal with the problems in this link according to the situation, and pay attention to the details in this link.
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
According to the functional data learned by Xiao Bian, the temperature of the lit cigarette is about 700 ℃, and the continuous burning time of a cigarette is about 15 minutes, which is a long time. However, the spontaneous ignition point of common combustibles is very low, such as paper, cotton, linen and knitted fabrics, whose ignition point is mostly 200 ℃ to 300 ℃, so it is easy to cause fire. Turning to the statistics of major and catastrophic fires nationwide, there are many records of fires and casualty accidents caused by smoking after drinking, smoking in bed, littering cigarette butts and other reasons. The typical case is the Great Khingan Mountains forest fire in 1987, which caused a heavy loss of 6.913 billion yuan. It was later discovered that four of the first five fire spots of the fire were caused by human beings, and two of the fire spots were ignited by the cigarette butts of three "smokers".
