The basic process flow of knitting is: bleaching and dyeing - weft rolling - weaving - off machine cutting - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality. In 1980, SD-81A and B rubber ingot belts were developed, which are soft, light, thin, firm, with small elongation, small impact force, short and flat joints. At the beginning of 1990, the trial production of car seat belts for Santana cars was successful. After more than two years of research and trial production, the product quality reached QC49-92 and TL-VW470 standards.
Xiamen customized Braided rope Clear drawings within parameters: clear the drawings within the set range of longitude and latitude. Multiple maps to one map: insert multiple maps into one map in the longitudinal direction. One manufacturing to multiple manufacturing: turn in one drawing and disassemble it into multiple pieces in the longitudinal direction. Graph merging: after multiple graphs are handed over and inserted into one (that is, multiple weaving turns to one manufacturing), the whole warp yarn with one upper and lower weave is deleted. Computer jacquard webbing drawing sequence: analyze the weave rule of the jacquard webbing, and draw the "high" part of all characters or patterns in a cycle according to the weave rule determined by analysis and combined with the actual fabric, Xiamen customized Braided rope manufactor Then draw the "high" part of the bottom color (color other than text or pattern) in a cycle according to the organization rule. After all the "high" parts are drawn, draw the "low" part of the pattern and bottom according to the analyzed organization rule until the drawing is completed.
Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
The longitude and latitude are interwoven. [Subject] After twisting, the yarn is warped into a bobbin (pan head), and the weft yarn is shaken into a bobbin, which is woven on the loom. In the 1930s, it was used for hand looms and iron wood looms. In the early 1960s, the 1511 loom was converted into a belt loom, which is still widely used. Due to the small width of the belt, the weaving methods are different, ranging from single, double, dozens of pieces, from single layer to double layer. In 1967, the research group of shuttleless weaving belt with workers as the main body in the industry successfully designed and manufactured a high-speed single shuttleless loom by itself, which realized that the weaving belt does not need shuttles, and the process is shortened, the floor area is small, and the labor productivity is improved, which is an innovation in the history of Chinese weaving belt technology.
What type is this? For example: ribbon, plaid belt, jacquard webbing, cotton belt and other products, these should be distinguished first. What is the size? The width and thickness should be understood clearly. What material is this ribbon? Different materials mean different prices. What color is it? How many colors are there? This also needs to be made clear. For example, single color ribbons should be cheaper, while multi color ribbons must be more expensive. Do you need dyeing? Some ribbons are dyed by the customer, and the price of dyeing is different.
