Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
Woven belt manufactor The progress of process technology has brought about the upgrading of edging webbing products. In 1979, the trial production of the domestic generation SD9-9 rubber ingot belt was successful, which ended the history of rubber ingot belt products relying on imports. After the weft tube is formed by the yarn warp cylinder and weft winding, it is inserted on the fixed gear seat of the knitting machine, and the weft tube rotates along the 8-shaped track to draw the yarns to cross weave with each other. Fuzhou special Woven belt Usually, the number of spindles is even, the woven tape is tubular, the number of spindles is odd, and the woven tape is flat. Spindle weaving technology has been applied since old China. The number of spindles varies from 9 to 100 due to different equipment.
Width detection: the tolerance of webbing with width of 1 "and above shall not exceed ± 0.25 points; The tolerance of webbing with width of 25MM and above shall not exceed ± 0.5MM; The standard tolerance of webbing width of 1 "and less than 25MM shall not exceed ± 0.25MM; Note: The flat end and herringbone edging webbing must be of sufficient size, but not more than 0.25 points. Thickness inspection: the tolerance shall not exceed ± 0.1MM; Color difference test: there is no yin and yang color on the belt surface by naked eye, and the needle edge and cloth edge cannot be exchanged for the color and texture (the needle edge of each woven belt must be of one color). Singeing and labeling: Each bag ribbon must be singed thoroughly, but cannot be burnt. The quality inspector shall inspect the packaging label to be consistent with the actual goods (specification, color, quantity), and seal it for warehousing. If errors and omissions are found, the relevant processes shall be traced in time, and the relevant personnel shall be held accountable according to the seriousness of the case.
Ink printing. At first glance, ink is not very different from glue, but when glue is printed on smooth fabrics, such as wind clothing, the color fastness is generally poor, and it can be scraped off with a nail, but ink can overcome this shortcoming. Therefore, when making windbreaker, it is usually printed with ink, with bright color and vivid image. There has been a wave of head prints in the market some time ago~I don't know if you have noticed it, then the clear and ultra realistic printing can only be printed with ink in general~Sometimes you can sprinkle gold powder and silver powder on the ink, and feel that the decoration effect is better.
The printing is in the passenger compartment to enhance the matching and coordination with the color in the cabin. The binding ribbon printing will be dyed into various colors. People always hope that the color dyed will not fade within the specified time. Therefore, the belt has a specific color fastness test. The wrapped webbing belt is exposed to light, and like other substances, it will fade. The wrapped webbing has this characteristic, which is called light color fastness. In this test, the webbing is placed under representative strong light and exposed to the specified time. Then compare the bag webbing with the standard color card to evaluate a fading grade.
One of the complete knowledge of printing types. There are many kinds of bag ribbon printing. Today, it is divided into two parts for everyone to talk about. If you like it, you can have a detailed look. It should be helpful to you. Here is the first part. Bag webbing transfer printing. The pigment is printed on the paper by printing method to make transfer printing paper, and then the color is transferred to the fabric by high temperature (heating and pressing on the back of the paper). It is generally used for chemical fiber fabrics, characterized by bright colors, fine layers, lifelike patterns, and strong artistry. However, this process is currently only applicable to a few synthetic fibers such as polyester. Transfer printing process is simple, investment is small and production is flexible. It is popular in the market at present But to be honest, compared with other types of printing, the price of this transfer printing is a little high, but it has a certain level.
