Surface fuzzing. The case and bag webbing surface fuzzing and needle edge defects often occur in the production process. What are the reasons and how to solve or prevent them? The following manufacturer's knitting will tell you. Causes of surface fuzzing of luggage webbing: needle edge fuzzing, cloth edge fuzzing. Precautions: The needle plate has been used for a long time and has been damaged. Replace the needle plate with a new one; The knitting needle has been damaged and replaced with a new one; The pressure plate is pressed too tightly, and loosen the pressure plate; If the weft is not hung completely, adjust the distance between the weft needle and the knitting needle so that the weft can be hung completely. The steel buckle of the weft yarn is hung, and the weft yarn is put into the weft rod; If the steel buckle is damaged, replace it with another one; The raw material itself is hairy. If it is partly hairy, replace it. If it is too hairy, make a full inspection belt after finishing the goods.
The unused ones from the knitting production line are called. The strength, width, thickness, elongation and stiffness described above are all measured on the knitting production line. The data measured on the knitting production line are called data. The safety belt installed in the car should be worn by the passengers after they get on the car. The use process is an aging process, and its strength will decline. In order to ensure that the safety belt can effectively protect the passengers before the vehicle is scrapped, the strength of the webbing shall be measured after simulating the working conditions. This strength is called the strength after the environmental test. After the environmental test, the strength includes light treatment, low temperature treatment, high temperature treatment, immersion test and wear treatment.
Indirect plate making method: the indirect film is first exposed, hardened with 1.2% H2O2, developed with warm water, and dried to make a strippable graphic negative. During plate making, the adhesive film surface of the graphic negative is closely attached to the stretched screen, the adhesive film is tightly attached to the wet screen by extrusion, the film base is removed, and the screen is dried by wind. Process flow: 1. Stretched wire mesh - degreasing - drying. 2 Indirect film - exposure - hardening - development - fitting - drying - revision - blocking. 3 Straight mixed plate making method: first, paste the photosensitive adhesive layer on the screen frame with water, alcohol or photosensitive adhesive, dry it with hot air, remove the substrate of the photosensitive film, and then print the plate. After developing, the screen plate is made.
The moisture in the air may cause spots in the car. When this kind of webbing contacts the clothes of passengers, the spots and colors on the luggage webbing will also be transferred to the clothes. Therefore, it should have anti spot fading characteristics, which is also called spot color fastness. The spot color fastness test includes multi fiber test and filter paper test. The multi fiber test is to clamp a sample of tissue belt between two layers of colored cloth. Immerse the mixed colored cloth into the vessel with distilled water and completely wet it. Then squeeze the water out of the extruder, and then clamp these colored cloth wrapped with selvedge webbing into the plexiglass sheet, put it into the sample holder, and lock the sample holder. This rack is placed in a high and low temperature box at a certain temperature, and after reaching the specified time. Take out the sample and hang the colored cloth.
Computer drawing process. Many friends are particularly interested in computers. Xiao Bian has briefly introduced the textile technology of computer jacquard belts before, but many people are still interested in how to draw computer jacquard belts. Today, we will introduce its drawing method according to the drawing process of the ribbon. Single color change: change the color of the left or right mouse button in the picture according to the position within the parameter range, and change the color of a connected color block within the parameter range. The color changed depends on whether the left or right mouse button is pressed. Select a rectangular range: click two points in the editing area to form a rectangular range with these two points as the opposite corners, so that you can clear, cut, copy, and organize this rectangular range. Clear out of parameter drawings: Clear the drawings outside the set range of longitude and latitude.
Single and double layer webbing Manufacturer The tensile strength after light treatment, the natural light shines on the bag webbing through the window, causing aging and reducing its strength. According to the working conditions, a lighting equipment is designed, which is equipped with representative strong light and is exposed to the light for a specified time. After lighting, pp webbing needs to be subjected to standard temperature and humidity treatment, and then to tensile test to obtain the tensile strength after lighting treatment. Single and double layer webbing Manufacturer After soaking, the tensile strength of the safety belt installed in the car will absorb the moisture in the air, and sometimes it will be soaked by some liquid, so special Single and double layer webbing Water immersion test is required. At room temperature special Single and double layer webbing Fully immerse in distilled water with a small amount of wetting agent for a specified time, and then take out the soaked pp webbing from the water to complete the tensile test within 10 minutes. The tensile strength of soaked pp webbing was obtained.
