According to the functional data learned by Xiao Bian, the temperature of the lit cigarette is about 700 ℃, and the continuous burning time of a cigarette is about 15 minutes, which is a long time. However, the spontaneous ignition point of common combustibles is very low, such as paper, cotton, linen and knitted fabrics, whose ignition point is mostly 200 ℃ to 300 ℃, so it is easy to cause fire. Turning to the statistics of major and catastrophic fires nationwide, there are many records of fires and casualty accidents caused by smoking after drinking, smoking in bed, littering cigarette butts and other reasons. The typical case is the Great Khingan Mountains forest fire in 1987, which caused a heavy loss of 6.913 billion yuan. It was later discovered that four of the first five fire spots of the fire were caused by human beings, and two of the fire spots were ignited by the cigarette butts of three "smokers".
Hygiene: It is a natural fiber, and its main component is cellulose, with a small amount of waxy substances, nitrogen and pectin. After various inspections and practices, the pure cotton ribbon has no stimulation or negative effect when contacting with the skin. It is beneficial to the human body and has good sanitary performance after being worn for a long time. Heat resistance: the heat resistance is good. When the temperature is below 110 ℃, it will only cause water evaporation on the webbing and will not damage the fiber. Therefore, the use, washing, printing and dyeing of pure cotton webbing at room temperature have no impact on the webbing, which improves the washing and wear resistance of pure cotton edging webbing.
After the weft tube is formed by the yarn warp cylinder and weft winding, it is inserted on the fixed gear seat of the knitting machine, and the weft tube rotates along the 8-shaped track to draw the yarns to cross weave with each other. Usually, the number of spindles is even, the woven tape is tubular, the number of spindles is odd, and the woven tape is flat. Spindle weaving technology has been applied since old China. The number of spindles varies from 9 to 100 due to different equipment. The basic process of weaving is: bleaching and dyeing - weft rolling - weaving - off machine shearing - packaging. Since 1960, many technical innovations have been carried out on the knitting machine, mainly including the enlargement of peach plate diameter, the installation of an automatic stop device for breaking rubber bands, and the replacement of iron ingots with nylon ingots. The improvement of these equipment has increased the vehicle speed to 160~190 rpm, doubled the stand rate and greatly improved the product quality.
Customized Cotton ribbon It may be due to the use of too much thinner, especially the poor compatibility of thinner and ink, which causes color bleeding during PP textile printing. It may be that there is color seeping on the edge of the printed image and text, which is a common phenomenon, so don't worry too much. It can be solved by ordinary methods. It may be caused by the selection of dyes in the ink, or it can be said that make well-connected Customized Cotton ribbon It is caused by improper matching of pigments. We can deal with the problems in this link according to the situation, and pay attention to the details in this link.
Not only the production process is complex, but also the packaging process is very complicated. Only the webbing that has passed the inspection can be packaged out of the warehouse, otherwise it will be treated as defective products. The specific packaging process is as follows: 1. The process control method: 1. The surface of each winding tape must be smooth and flat (except for special webbing); Those who cannot be involved in substandard products shall be held accountable according to the seriousness of the case. Knot: ≤ 3/100Y, ≤ 2/50Y; Short code: ± 0.5/100Y; Each knapsack strap must have the label of the tape coiler. Inspection according to the customer's requirements: for example, 336, 217, 115, 314, 108, 114, 384, 206, 419, 122 adhesive paper and rubber hose, no pins can be used;
The unused ones from the knitting production line are called. The strength, width, thickness, elongation and stiffness described above are all measured on the knitting production line. The data measured on the knitting production line are called data. The safety belt installed in the car should be worn by the passengers after they get on the car. The use process is an aging process, and its strength will decline. In order to ensure that the safety belt can effectively protect the passengers before the vehicle is scrapped, the strength of the webbing shall be measured after simulating the working conditions. This strength is called the strength after the environmental test. After the environmental test, the strength includes light treatment, low temperature treatment, high temperature treatment, immersion test and wear treatment.
